Shortening a Chain
Model Engineers' Workshop|April 2020
Will Doggett makes a special link to shorten the Hand Chain on a lifting block
Will Doggett
Shortening a Chain

This article is about shortening a continuous hand chain on a chain block and shortening must not be done this way on a load chain under any circumstances as this would be very dangerous. To shorten a load chain the hook is removed the chain is then cut to the required length then the hook is replaced it is making it longer that you must not do.

The concept and history

Photo 1 show the finished article, actually this is not the one that is described in this article, it is one I made earlier. After sorting out and moving things in the workshop I found a feed bag with my chain block in it, I open the bag to find to my shame that both the chains, load and hand chain, had some rust on them. The rust most likely accrued in winter when the temperature changes from cold to hot in a very short time causing condensation in the bag, as it was stored in unheated building – well this is my defence.

To clean them up I was going to use a Citric acid and water bath this required the chains to be removed from the block. The hand chain was removed first it seamed long. I remembered that when I used the block the last time to put the Mill/Drill on its stand the hand chain was too long and getting in the way as it piled up on the floor but in the rush to use the new toy the block was put away and forgotten about. The answer to this problem was to make the chain shorter before cleaning the chain as there was no point in cleaning the bit that was not required.

هذه القصة مأخوذة من طبعة April 2020 من Model Engineers' Workshop.

ابدأ النسخة التجريبية المجانية من Magzter GOLD لمدة 7 أيام للوصول إلى آلاف القصص المتميزة المنسقة وأكثر من 9,000 مجلة وصحيفة.

هذه القصة مأخوذة من طبعة April 2020 من Model Engineers' Workshop.

ابدأ النسخة التجريبية المجانية من Magzter GOLD لمدة 7 أيام للوصول إلى آلاف القصص المتميزة المنسقة وأكثر من 9,000 مجلة وصحيفة.

المزيد من القصص من MODEL ENGINEERS' WORKSHOP مشاهدة الكل
Readers' Workshops - Patrick Cubbon
Model Engineers' Workshop

Readers' Workshops - Patrick Cubbon

Patrick Cubbon describes his workshops – a portable one from 1963 and the current accommodation

time-read
2 mins  |
May 2020
Desktop Gear Hobbing
Model Engineers' Workshop

Desktop Gear Hobbing

Toby Kinsey has designed this fascinating piece of gearmaking equipment

time-read
9 mins  |
May 2020
The John Stevenson Trophy 2020
Model Engineers' Workshop

The John Stevenson Trophy 2020

Many readers and forum members will remember John Stevenson, a contributor to MEW but best known for his larger-than life presence on the Model Engineer forum.

time-read
3 mins  |
May 2020
From the Archives: Twist drill Sharpening by the Four Facet Method
Model Engineers' Workshop

From the Archives: Twist drill Sharpening by the Four Facet Method

Giles Parkes, MEW Issue 64, February/March 2000

time-read
4 mins  |
May 2020
Dividing on the Warco 220 Lathe
Model Engineers' Workshop

Dividing on the Warco 220 Lathe

Peter Shaw describes a mandrel dividing attachment for this popular lathe that can be adapted to fit many other benchtop machines

time-read
8 mins  |
May 2020
Choosing Steels
Model Engineers' Workshop

Choosing Steels

Stub Mandrel offers some advice on choosing the right steel for the job

time-read
7 mins  |
May 2020
A Storage Story
Model Engineers' Workshop

A Storage Story

Robin King shares the lessons learned from his experience of workshop moves

time-read
8 mins  |
May 2020
A Simple Drill Grinding Aid
Model Engineers' Workshop

A Simple Drill Grinding Aid

A newcomer to our hobby was having trouble sharpening drills, so Howard Lewis made a simple aid for him

time-read
2 mins  |
May 2020
Yet Another Bodge-Up!
Model Engineers' Workshop

Yet Another Bodge-Up!

Peter Shaw finds a use for some aged homebrew slot drills.

time-read
5 mins  |
March 2020
Workshop Press Tooling Part 2
Model Engineers' Workshop

Workshop Press Tooling Part 2

Will Doggett makes a set of tooling for his press tool described starting in issue 285

time-read
5 mins  |
March 2020