Repairing a ‘Safe-D-Speeder'
Model Engineers' Workshop|March 2020
R. Finch saves a useful device from the scrap box
R. Finch
Repairing a ‘Safe-D-Speeder'

About 20 years ago, I was given a Mason Master ‘Safe-D-Speeder’ epicyclic speed reducer, photo 1, which I thought might come in useful one day, so I kept it in one of the drawers of my tool chest. When the D-speeder was made in the 1950s, electric drills were pretty well all single speed of around 2800 rpm and had 1/4 inch capacity chucks. If there were a need to drill into masonry or use a larger drill, then the only speed reduction method was to use the D-speeder with its 3/8 inch chuck. The method of use was to hold the 1/4 inch input shaft in the electric drill chuck and the masonry drill bit in the chuck on the D-Speeder, whilst gripping the outside of the casing with the hand to stop the body rotating. This gave a four to one reduction in speed and consequently a four times increase in torque. If the drill bit jammed in the hole, the outer casing would try to rotate and, unless you had bionic hands, it would slip in your hand and not stall the electric drill.

As I already had a two-speed drill, I never used the de-speeder until I came to use a 100mm hole saw to drill an access hole through a floorboard for installing new cables for my Internet connection. My drill, even on low speed (850 rpm), was still rather too fast for such a large hole saw and it tended to overload the drill. I then remembered the D-speeder that had lain unused for all those years and dug it out, only to find that it had almost seized up. It was very stiff to turn and clearly needed a bit of attention.

The instructions

Esta historia es de la edición March 2020 de Model Engineers' Workshop.

Comience su prueba gratuita de Magzter GOLD de 7 días para acceder a miles de historias premium seleccionadas y a más de 9,000 revistas y periódicos.

Esta historia es de la edición March 2020 de Model Engineers' Workshop.

Comience su prueba gratuita de Magzter GOLD de 7 días para acceder a miles de historias premium seleccionadas y a más de 9,000 revistas y periódicos.

MÁS HISTORIAS DE MODEL ENGINEERS' WORKSHOPVer todo
Readers' Workshops - Patrick Cubbon
Model Engineers' Workshop

Readers' Workshops - Patrick Cubbon

Patrick Cubbon describes his workshops – a portable one from 1963 and the current accommodation

time-read
2 minutos  |
May 2020
Desktop Gear Hobbing
Model Engineers' Workshop

Desktop Gear Hobbing

Toby Kinsey has designed this fascinating piece of gearmaking equipment

time-read
9 minutos  |
May 2020
The John Stevenson Trophy 2020
Model Engineers' Workshop

The John Stevenson Trophy 2020

Many readers and forum members will remember John Stevenson, a contributor to MEW but best known for his larger-than life presence on the Model Engineer forum.

time-read
3 minutos  |
May 2020
From the Archives: Twist drill Sharpening by the Four Facet Method
Model Engineers' Workshop

From the Archives: Twist drill Sharpening by the Four Facet Method

Giles Parkes, MEW Issue 64, February/March 2000

time-read
4 minutos  |
May 2020
Dividing on the Warco 220 Lathe
Model Engineers' Workshop

Dividing on the Warco 220 Lathe

Peter Shaw describes a mandrel dividing attachment for this popular lathe that can be adapted to fit many other benchtop machines

time-read
8 minutos  |
May 2020
Choosing Steels
Model Engineers' Workshop

Choosing Steels

Stub Mandrel offers some advice on choosing the right steel for the job

time-read
7 minutos  |
May 2020
A Storage Story
Model Engineers' Workshop

A Storage Story

Robin King shares the lessons learned from his experience of workshop moves

time-read
8 minutos  |
May 2020
A Simple Drill Grinding Aid
Model Engineers' Workshop

A Simple Drill Grinding Aid

A newcomer to our hobby was having trouble sharpening drills, so Howard Lewis made a simple aid for him

time-read
2 minutos  |
May 2020
Yet Another Bodge-Up!
Model Engineers' Workshop

Yet Another Bodge-Up!

Peter Shaw finds a use for some aged homebrew slot drills.

time-read
5 minutos  |
March 2020
Workshop Press Tooling Part 2
Model Engineers' Workshop

Workshop Press Tooling Part 2

Will Doggett makes a set of tooling for his press tool described starting in issue 285

time-read
5 minutos  |
March 2020