Garden Tractor Refurbishment
Model Engineers' Workshop|March 2020
Stan Nesbitt uses his workshop to rescue some garden machinery.
Stan Nesbitt
Garden Tractor Refurbishment

When I spotted two scrap Westwood ride-on lawnmowers for sale locally I acquired them intending to recover pulleys, bearings, drive belts and engines etc. for use in other projects. These older Westwood tractors are heavily built using sheet steel throughout. The engines were Briggs & Stratton. I was horrified to discover on one engine that part of the crankshaft had been sawn off to recover the cast iron pulley. However, the pulley was found amongst other parts still firmly attached to the piece of crankshaft! Photo 1.

After further examination I concluded that it was worthwhile refurbishing the smaller unit, the S800, photo 2. I managed to purchase an 8 hp Briggs & Stratton engine which only needed a de-coke, the valves regrinding and a new set of piston rings. This engine has both a pull start and electric start which is a useful feature if the battery is flat photo 3.

Where the paintwork fails, surface rust quickly appears especially where panels are bolted together. Nuts and bolts on these American machines are all imperial so I had to dig out the appropriate and seldom-used spanners. An electric impact driver proved very useful and avoided shearing rusty examples, photos 4 & 5.

These older models were fitted with expensive and well-made gearboxes having five forward and one reverse gear and incorporating a differential. Later models like the Lawnflite use a simple adjustable double pulley which provides for speed changes. A differential is fitted between the rear wheels and uses a separate forward, neutral and reverse control lever, photo 6.

Bu hikaye Model Engineers' Workshop dergisinin March 2020 sayısından alınmıştır.

Start your 7-day Magzter GOLD free trial to access thousands of curated premium stories, and 9,000+ magazines and newspapers.

Bu hikaye Model Engineers' Workshop dergisinin March 2020 sayısından alınmıştır.

Start your 7-day Magzter GOLD free trial to access thousands of curated premium stories, and 9,000+ magazines and newspapers.

MODEL ENGINEERS' WORKSHOP DERGISINDEN DAHA FAZLA HIKAYETümünü görüntüle
Readers' Workshops - Patrick Cubbon
Model Engineers' Workshop

Readers' Workshops - Patrick Cubbon

Patrick Cubbon describes his workshops – a portable one from 1963 and the current accommodation

time-read
2 dak  |
May 2020
Desktop Gear Hobbing
Model Engineers' Workshop

Desktop Gear Hobbing

Toby Kinsey has designed this fascinating piece of gearmaking equipment

time-read
9 dak  |
May 2020
The John Stevenson Trophy 2020
Model Engineers' Workshop

The John Stevenson Trophy 2020

Many readers and forum members will remember John Stevenson, a contributor to MEW but best known for his larger-than life presence on the Model Engineer forum.

time-read
3 dak  |
May 2020
From the Archives: Twist drill Sharpening by the Four Facet Method
Model Engineers' Workshop

From the Archives: Twist drill Sharpening by the Four Facet Method

Giles Parkes, MEW Issue 64, February/March 2000

time-read
4 dak  |
May 2020
Dividing on the Warco 220 Lathe
Model Engineers' Workshop

Dividing on the Warco 220 Lathe

Peter Shaw describes a mandrel dividing attachment for this popular lathe that can be adapted to fit many other benchtop machines

time-read
8 dak  |
May 2020
Choosing Steels
Model Engineers' Workshop

Choosing Steels

Stub Mandrel offers some advice on choosing the right steel for the job

time-read
7 dak  |
May 2020
A Storage Story
Model Engineers' Workshop

A Storage Story

Robin King shares the lessons learned from his experience of workshop moves

time-read
8 dak  |
May 2020
A Simple Drill Grinding Aid
Model Engineers' Workshop

A Simple Drill Grinding Aid

A newcomer to our hobby was having trouble sharpening drills, so Howard Lewis made a simple aid for him

time-read
2 dak  |
May 2020
Yet Another Bodge-Up!
Model Engineers' Workshop

Yet Another Bodge-Up!

Peter Shaw finds a use for some aged homebrew slot drills.

time-read
5 dak  |
March 2020
Workshop Press Tooling Part 2
Model Engineers' Workshop

Workshop Press Tooling Part 2

Will Doggett makes a set of tooling for his press tool described starting in issue 285

time-read
5 dak  |
March 2020