Cog-swapping! Kawasaki H2C part 5
Classic Motorcycle Mechanics|May 2020
Seems like our Ralph is back with the terror that is the purple pain! What now, Un-Wreck It Ralph?
RALPH FERRAND
Cog-swapping! Kawasaki H2C part 5

It seems some time since we last spoke about themyriad failings of my purple nemesis. I am now in a position to start re-assembling the two-wheeled smog monster.

My gearbox arrived back at Chez Ferrand with all the broken bits replaced with used replacements that had undergone a serious health check, so I should now have all the ingredients for a good robust cog-swapper.

To kick-off I fitted the upper crankcase in my home-brewed engine building frame and selected a nice sharp wood chisel to remove the remains of old base gaskets from the mouths of the crankcase.

I cannot over-emphasise how important it is to do this tedious job with maximum care and full concentration, as any chunks taken out of the gasket surface can cause leaks that would have a devastating effect on the good running of the two-stroke engine. After flipping over the crankcase, I started to repopulate it with all the gear changing components.

First back in was the shift drum and selector forks. It’s a fairly simple task, sliding the selector forks over the drum in their correct position as you push it in. Once the drum is in, you can engage the guide pins that follow the contours of the drum groove in each of the three selector fork bosses. These then can be tightened up and the tab washers flattened against the flats of their spanner hexes to prevent them undoing, which would likely destroy the box. Then the securing plate was fitted on the outside, followed by the indent lever that engages on pins on the end of the drum to ensure that the bike stays in the gears selected.

Esta historia es de la edición May 2020 de Classic Motorcycle Mechanics.

Comience su prueba gratuita de Magzter GOLD de 7 días para acceder a miles de historias premium seleccionadas y a más de 9,000 revistas y periódicos.

Esta historia es de la edición May 2020 de Classic Motorcycle Mechanics.

Comience su prueba gratuita de Magzter GOLD de 7 días para acceder a miles de historias premium seleccionadas y a más de 9,000 revistas y periódicos.

MÁS HISTORIAS DE CLASSIC MOTORCYCLE MECHANICSVer todo
Classic Motorcycle Mechanics

Honda VFR750R - RC30

If there’s a more worshipped V4 out there, we’ve yet to see it: welcome to our reboot of the awesome VFR750R RC30…

time-read
2 minutos  |
September 2021
Mountain tension!
Classic Motorcycle Mechanics

Mountain tension!

Award-winning motorcycle engineer!

time-read
5 minutos  |
September 2021
Fazer set to STUN!
Classic Motorcycle Mechanics

Fazer set to STUN!

What do you get when you mix CRK’s lovely café racer kit to Yamaha’s budget middleweight and the recently-retired Martin Fox? Well, one helluva foxy Fazer!

time-read
6 minutos  |
September 2021
Project Suzuki 1984 RG250 part 4 BRUNO BARES ALL!
Classic Motorcycle Mechanics

Project Suzuki 1984 RG250 part 4 BRUNO BARES ALL!

This month, while we wait for backorder engine parts, we strip the chassis back to the bare frame, assess what is needed and plan the reassembly…

time-read
6 minutos  |
September 2021
Project Kawasaki Z900 Stocker part 2 Ralph has a blast!
Classic Motorcycle Mechanics

Project Kawasaki Z900 Stocker part 2 Ralph has a blast!

For the best finish on his Z900’s motor Ralph wants the best, so he visits Stephen Smethurst Casting Renovation to find out how it’s done properly.

time-read
10 minutos  |
September 2021
Project Suzuki TS400 Part 8 Loom with a view!
Classic Motorcycle Mechanics

Project Suzuki TS400 Part 8 Loom with a view!

We’re getting down into the nitty-gritty this time with component testing and loom building. What could go wrong?

time-read
6 minutos  |
September 2021
Project Yamaha TX750 Part 12 A question of balance…
Classic Motorcycle Mechanics

Project Yamaha TX750 Part 12 A question of balance…

Only The Beach Boys had good vibrations… so what’s Mark been up to, to sort out the bad ones coming from his TX750?

time-read
6 minutos  |
September 2021
Splitting links
Classic Motorcycle Mechanics

Splitting links

Ralph Ferrand works with tools all day long – he sells them too at bikerstoolbox.co.uk so he knows what works.

time-read
4 minutos  |
September 2021
Classic Motorcycle Mechanics

STAVROS: PRINCE OF PRANKSTERS!

It’s probably fair to say that Stephen JamesParrish’s persona and overall levity throughout his life have muddied the waters as to just how good a bike racer he was back in the day.

time-read
1 min  |
September 2021
Metal magic!
Classic Motorcycle Mechanics

Metal magic!

Ralph Ferrand works with tools all day long – he sells them too at bikerstoolbox co uk so he knows what works.. .

time-read
3 minutos  |
July 2021